1. 動力采用康明斯發動機，功率為500HP。

1. Cummins engine is adopted as the power, and the power is 500hp.

2. 作業轉子驅動采用機械（皮帶）傳動，動力傳動比液壓傳動效率提高25%，皮帶傳動使沖擊載荷免于傳到發動機上，根據不同的負載情況通過置換皮帶輪可得到不同的轉速。

2. The operating rotor is driven by mechanical (belt) transmission. The power transmission efficiency is 25% higher than that of hydraulic transmission. Belt transmission prevents the impact load from being transmitted to the engine. Different speeds can be obtained by replacing the belt pulley according to different load conditions.

3. 轉向方式有前輪轉向、蟹型轉向、后輪轉向、全輪轉向，因此具有良好的機動性能。

3. The steering modes include front wheel steering, crab steering, rear wheel steering and all wheel steering, so it has good maneuverability.

4. 本機具有功率自動分配功能，當銑拌阻力增加發動機轉速下降時，微控器能夠調節行走系統的功率，補償銑拌系統的功率，保證該機在大效率和大生產率狀態下工作。

4. The machine has the function of automatic power distribution. When the milling and mixing resistance increases and the engine speed decreases, the microcontroller can adjust the power of the walking system and compensate the power of the milling and mixing system to ensure that the machine works under the state of maximum efficiency and productivity.

5. 液體噴灑計量系統，微控器能夠根據行走速度銑拌深度及銑拌寬度自動調節噴灑量的大小，實現噴灑量的精確計量控制，滿足舊瀝青路面的再生要求。

5. For the liquid spraying metering system, the micro controller can automatically adjust the spraying amount according to the walking speed, milling depth and milling width, so as to realize the accurate metering control of the spraying amount and meet the regeneration requirements of the old asphalt pavement.

6. 裝備MOBA銑刨機找平系統，MOBA銑刨機找平系統專為控制銑刨機工作時的銑刨深度設計，通過傳感器對銑刨鼓相對于銑刨機機身位置的距離變化進行檢測，將變化量轉化為電信號傳輸給控制器，再由控制器自動對銑刨鼓進行調整，從而實現對銑刨深度的自動控制。

6. The MoBa milling machine leveling system is equipped. The MoBa milling machine leveling system is specially designed to control the milling depth when the milling machine is working. The distance change of the milling drum relative to the body position of the milling machine is detected through the sensor, the change is converted into an electrical signal and transmitted to the controller, and then the controller automatically adjusts the milling drum, so as to realize the automatic control of the milling depth.

7. 本機具有GPS遠程故障診斷系統，使用GPS遠程監控系統，可實現設備的全球定位、設備工作信息監控、故障診斷、遠程維護和報警，以及鎖車、防盜等功能。通過嵌入式計算機技術和移動通信技術搭建的服務管理平臺，能通過網絡終端實時遠程監控，實施遠程管理。

7. The machine has a GPS remote fault diagnosis system. Using the GPS remote monitoring system, it can realize the functions of equipment global positioning, equipment work information monitoring, fault diagnosis, remote maintenance and alarm, as well as vehicle locking and anti-theft. The service management platform built by embedded computer technology and mobile communication technology can realize real-time remote monitoring and remote management through network terminal.

（1）能夠遠程觀測到設備所處的地理位置以及現場施工軌跡及觀測到其施工區范圍。

(1) It can remotely observe the geographical location of the equipment, the on-site construction track and the scope of its construction area.

（2）能夠進行車輛發動機各項參數、工作狀態、油壓的運行情況和運行異常報警預告的實時信息狀態查。

(2) It can check the real-time information status of vehicle engine parameters, working status, oil pressure operation and abnormal operation alarm.

今天的分享就是關于冷再生機租賃，更多的內容小編會不斷的再此分享，更多的內容請繼續關注我們：http://m.wlc189.com

Today's sharing is about the rental of cold regenerator. More content will be shared here. Please continue to pay attention to us: http://m.wlc189.com